Revell AG 1/32 He-162A Volksjaeger

KIT #: ?
PRICE: $29.95 MSRP
DECALS: Three options
REVIEWER: Tom Cleaver


      The Heinkel He-162 fighter is a perfect demonstration of the dream world Hitler and his Nazis lived in.  Had the leadership of Germany been willing to see the writing on the wall even as late as “Big Week” in February 1944 and conclude that Germany needed to put all its resources into defense, this airplane might have had an effect on the Second World War, though the ultimate result would have been merely to delay the inevitable by at most 18 months.  In the space between February and September, when reality was finally confronted, such was the pace of Allied success with the invasion of Normandy and the expulsion of German forces from all Soviet territory on the Eastern Front that the die had been cast and there was nothing to be accomplished in the production of the aircraft.

      The main claim to fame of the He-162 was the phenomenally short time that elapsed from its conception to the flight of the first prototype - just less than three months.  The airplane was born of the necessity to create an interceptor with the performance of the Me-262, costing less and using non-essential materials, to be of such simple design that it could be rapidly produced by semi-skilled labor.

      The specification for what would become the He-162 was issued on September 8, 1945; it called for an aircraft that would be regarded as “a piece of consumer goods”, that would be ready to enter operational use by January 1, 1945. Seven companies were invited to submit proposals - Arado, Blohm und Voss, Fieseler, Focke-Wulf, Heinkel, Junkers and Messerschmitt.  Messerschmitt flatly refused to participate, leaving Heinkel as the only competitor with any actual jet aircraft design experience, having built the world’s first jet, the He-178, and first jet fighter, the He-280.

      The designs submitted by Heinkel and Blohm und Voss were judged best on September 15, 1944, though the Blohm und Voss project would be abandoned on September 30.  Heinkel completed final design work on September 23, and a small mock-up was inspected by the RLM.  This was followed by the award of a contract for 1,000 He-162s per month, with mass production to begin no later than January 1, 1945.

      All design work was completed by October 29, when the blueprints and drawings were sent to the workshops, and production of the prototypes commenced.

      The He-162-V1 took to the air for its first flight on December 6, 1944.  The official first flight took place on December 10, before many Luftwaffe officials.  As Chief test pilot, Flugkapitaen Peter came across the field in a high-speed run, the starboard wing leading edge split, the aileron and wingtip tore away, and the prototype executed three quick rolls before crashing in front of the audience.  Three more prototypes and 30 He-162A-0s entered flight test between December 15, 1944, and February 28, 1945.  As a result of these tests, several modifications were adopted, including lengthened and down-turned wingtips, turning up the wing root, and placing spoilers on the leading edge near the fuselage.  The rudders were also enlarged to provide directional stability.  With these modifications, the flight characteristics were much improved, but it was obvious that the Nazi plans of sending thousands of ill-trained Hitler Jugend aloft in this demanding airplane were another fantasy.   

     Operational testing of the He-162 was assigned to Erprobungskommando 162, under the command of Heinz Baer at Rechlin. I/JG1 left the Eastern Front on February 6, 1945, to convert onto the He-162A-2 at Parchim. On completion of training on April 8, 1945, the unit transferred to Ludwigslust, while II/JG1 was transferred to Warnemuende in late March to commence conversion training.  While there is a rumor that an He-162A-2 of I/JG1 may have shot down an RAF Tempest in the last week of April 1945, there is no firm evidence of the He-162 ever entering combat before V-E Day on May 8, 1945.

      The British captured the 50 aircraft of I/JG1 at Leck on May 8.  By this time, over 1,000 He-162s had been produced in two underground factories, but Germany was too chaotic for them to get from factory to front line. 

      10 He-162s were brought to England after the war, where several were tested and a British test pilot was killed in one in November 1945 due to engine failure at low altitude.  Three of these were brought to the United States and tested at Freeman Field, Indiana in 1946.  Wk. Nr. 120077 went to Muroc Field in 1947, and was sold from there to a private collector as scrap in the early 1950s.  In 1958, Ed Maloney, founder of The Air Museum, Planes of Fame, began negotiations to purchase this airplane, and it arrived at the museum in 1961.  Today, this He-162 is one of the first aircraft a visitor sees on entering the Museum grounds in Chino, California.


     Revell’s He-162 is extremely simple in production layout, and it is obvious the kit has been “made for a price” when one opens the box.  Detail is OK for the landing gear, but anyone wanting to display the engine cowling open will want to replace the kit engine that is provided with a more detailed resin engine.  Airwaves have already brought out a resin seat and rear bulkhead, which is vastly superior to what is provided in the kit and was used in this review.  The decals provide full markings for three He-162A-2s of I/JG1, and are of acceptable quality.  Typical of Revell-Germany is the fact that there is no swastika provided.  This is easily solved by using swastikas from a 1/32 Bf-109 aftermarket sheet.


     Construction of the kit is extremely easy, due to the simplicity of the production design.  I spent more time pre-painting the cockpit in RLM66 and the landing gear and gear wells in RLM02 than I did in actual assembly.  I decided to close the engine cowling and the open gunbay, since what was inside was not particularly useful.  Fortunately, the gear wells and landing gear are nicely detailed, and the cockpit looks good once the resin ejection seat with Cutting Edge posable resin seat belts is installed.  I put four fishing weights in the nose, which was more than enough to guarantee nose-sitting.



      Since I was doing the He-162A I am most familiar with, the one at Planes of Fame in Chino, I painted the model in RLM65 Hellblau for the lower surfaces and RLM71 Dunkelgrun for the upper surfaces, since this is the way Wk. Nr. 120077 is painted, and that is the original Luftwaffe paint the airplane arrived in.

I used Xtracrylix for this.


      Kit decals were used with no problem, and a swastika was added from an Aeromaster 1/32Bf-109 aftermarket sheet.

      I gave the model a coat of Xtracrylix Satin Finish varnish, attached the landing gear and wheels, and set the cockpit canopy in the open position. 


      A very easy model that presents no problems in assembly and looks good when completed. This would be a good first kit for someone returning to the hobby after an extended absence, given the ease of construction.

January 2005

Copyright All rights reserved. No reproduction in part or in whole without express permission.

If you would like your product reviewed fairly and fairly quickly, please contact the editor or see other details in the Note to Contributors.

Back to the Main Page

Back to the Review Index Page  2022