Monogram 1/48 F-4C/D Phantom. 'High Tech'

KIT #: 5831
PRICE: $9.25 is what was on the sticker when purchased in 1990
DECALS: One markings option
REVIEWER: Scott Van Aken


Suffice it to say that there is probably as much if not more information available on the Phantom II than just about any other aircraft. It was one of those pivotal aircraft that was available at the right time and at the right place. When it first appeared in 1958, the prototypes went on to set a number of world records for speed and altitude, and while those have been eclipsed by newer military aircraft and specially prepared civilian war birds, it still left a lasting impression.

Even today, there are still a few Phantoms flying in defense of some countries in Europe and Asia, though I'm sure their tenure in the skies will soon be over after what is, after all, fifty years since first flight.


When Monogram released their 1/48 F-4 kits they were hailed as the best the industry had ever produced. Of course, for the time, they were right. Monogram was very much cutting edge in terms of detailing and accuracy. Even today, few injected kits can match the detailing in this kit's cockpit. Of course, the panel lines were the raised variety that was very much in vogue at the time, and the fit of some of the parts was a touch dodgy (like the lower intake), and there were more ejector pin marks that one could shake a stick at, but at the time, this was not a major concern to either modelers or the industry.

Unlike its replacement, the Hasegawa Phantom line, the Monogram kit came with a full array of weapons that included Sidewinders, Sparrows and centerline gun pod in the F-4C/D version. There were both wing and centerline fuel tanks as well. The landing gear were well made and sturdy. What's more, the main gear were properly canted slightly inboard as they are on the real aircraft. For those wondering, I'm using past tense as this kit has not been available on store shelves for many years. I'm not sure if Revell/Monogram is even thinking about reissuing it, though I'm sure that if they did, it would be well received.  As a side note, I pinched the sprues set up from another article. This boxing's plastic is in olive drab.

Anyway, the cockpit is a real beauty with nicely raised instrument and console detail. It has seats with belt detail already molded in place and it is correct for an F-4C. I think that there are panel differences for the avionics upgrade in the D, but most won't notice or care.

Another nice touch is that the outboard flaps/ailerons are molded in the slightly down position, a common sight for the plane on the ramp. Thee are two areas of concern. One is the lower fuselage/intake join which always seems to come up a bit short and needs a section of strip styrene. Another is that the stabilators seem to fit too far out from the fuselage. This is easily fixed with some trimming.

for rear view mirrors, some burner detailing and greater intake ramp detail than offered by the kit for the most part. Markings are for what was the oldest F-4 in the USAF inventory, that belonging to the 184 TFS, Arkansas ANG. The markings are fairly well printed, but rather thick and quite gloss. They can be usable, but you do have to take care of them when they get old. A good idea to get a back-up set of markings if you wish to do this version. Fortunately, the SEA scheme is well known and there are many other options should these markings not work out.


So there you have it. Monogram's 1/48 Phantom isn't as up to date as the Hasegawa kit in terms of molding technology, but if you have no problem with raised panel lines, then I know you will be happy with the results from this one. Probably the biggest difficulty will be finding one!

This one is straight out of my kit stash.

December 2008

If you would like your product reviewed fairly and fairly quickly, please contact the editor or see other details in the Note toContributors.

Back to the Main Page

Back to the Previews Index Page